mikesmarinefiberglassrepair.com

I am starting againWorking on a small chip repairI have to mix this color............Getting closerooooooo that's close I am spraying it on 3/13/21The bottom edge anLetting it dry for tomorrowwet sanded an buff 3/14I mix the color by eye Check it out , looks good 3/14/21

Starting an other boatA Proliner in with spider cracks on the sides 3/30/21Covering firstTapeing an coveringCovering an set up...........Spider Cracks about 2 foot longSome spider Cracks don't know whay their are doing , in the smooth an in the non-skid 3/30/21Aft deck floor corner spider crack , chop an ready to fill an sand smoothCracksMore cracks...........A spider Crack that is about 2 foot long , I have too tape off and cover thisBuff , clear ,tape off , an 3ft paper inside an outside , CHOPAn this small crack in the corner....3/30/21I am tape or chopping the surfacesBeforeAfter letting it dry 3/31I mix a color and did the bodywork an sprayed on the gelcoat , letting it dry 3/31Looks goodAn the other 2 spotsother corner 3/31/21I chop out the spider cracks an now making it ready too fiberglass . letting it dry 3/31/21I sprayed  the right side back corner 4/1/21The right side I sprayedwet sanded an buff 4/1/21Right side wet sanded an buff an clean up 4/2/21The spider cracks are gone , an refinish in gelcoat 4/2/21Saturday morning , its , finish the non skid , uncover the boat an wash it . 4/3/21 NEXT...........................

I have another boat , it's a Grady White that was in a firerI started too buff the surfaces , too get the color to shine . 3/15/21I remove the old MC numbersI had too wet sanded this surface to get the numbers off that was discolor from the old MC numbers glueThe left side is buff 3/15/21Finishing the back top an non-skid to get the surfaces clean to mix the color for this job.....Buffing again today 3/16buffingGetting shineycheck it out getting thereGunnel getting shiney or catwalkwas flat an faded , now shineybuffingOn the right side there is a crack that's needs repairing . So I chop it .Body work wet sanded flat an smoothI mix a color an sprayed it on ,3/17/21 letting it drywet sanded an buffsmooth an shineycorner repair .Refinish looks like new .......more repairs............Ready too fill 3/17/21Fill with fiberglass an let dry I use the gel I mix up an sprayed it on .............................3/18/21I got the boat buff an some touch ups finishI have the boat back in the building an cover , I started sanding off the burnt up gelcoat 3/22/21I have some body work to do on this job ...............3/22/213 ft paper the side Sanding an SandingSanding an sanding 3/24Block sanding SandingSandingI sprayed the gelcoat on 3/25/21DryingLetting the gelcoat drytape up and ready for gelcoat3/26ready too spray the gelcoatmix an sprayed the gelcoatLetting this dry too wet and an buff tomorrowwet sanding an buffing todayBuffedwet sanded an half buffed 3/27/21shiney buffSetting up too do the non-skidTaping offTape and paper off an the surface is sanded 3/28All ready to do the non-skidletting this dry 3/28/21Snaps are back on the boatCaulked all the old holes on the rub rail    3/29/21Washing the boat 4/3/21I did some caulking an put a new rub rail on the boat.........Caulked on ............New rub rail is on and caulk top an bottom............A nice straight line............I have the boat finish wash it an wax it....................